Eight grow room monitoring systems, sorted by need.

There's no single best grow room monitoring system for a commercial cannabis facility. It depends on the job. Some run the climate, some steer irrigation, some raise alarms and some measure the canopy. This guide holds eight to the same criteria, each fact sourced and dated: Agrowtek, AROYA, Grow Sensor, Growlink, Grownetics, Pulse, Sensaphone and TrolMaster. We make Grow Sensor, one of the eight.

By Tom Starley, Grow Sensor · Checked · 8 min read

A commercial cannabis flower room, with the canopy under trellis netting and rows of LED lights.
FIG. 01 · A commercial flower room

01 · The eight

Start with the job, not the brand.

A controller switches the room's equipment from its own sensors. A monitoring system measures and alerts, and leaves the switching to the controller. Crop steering sits between the two. It reads the root zone and runs irrigation. Find the need that sounds like yours.

The eight at a glance.

The eight at a glance, as each company lists it, checked 20 November 2026. Footnotes link to the sources; Grow Sensor's cells are from our own published specifications.
SystemKindControlsLeaf sensorAlerts byPrice to start
AgrowtekControllerClimate, lights, irrigation6Optional5Email, text6,7$319 sensor5
AROYACrop steeringIrrigation, HVAC triggers2,3,4Not listed1,3Not listed1,3,4$5K starter1
Grow SensorOursCrop steeringIrrigationBuilt inApp, push£699 / $899 system
GrowlinkPartnerControllerClimate, lights, irrigation8,10Aranet IR sensor9App10Not listed8,10
GrowneticsControllerClimate, CO₂, lights13Not listed12,13In its software14Software $249 a month14
PulseMonitoringNone listed15Not listed15Email, push, text16$199 Pulse One15
SensaphoneAlarmsNone listed17Not listed17,18Call, text, email17,18Not listed17,18
TrolMasterPartnerControllerClimate, lights, irrigation19,20Not listed19,20TM+ Pro app19,20$550 greenhouse kit21
The eight at a glance, as each company lists it, checked 20 November 2026. Footnotes link to the sources; Grow Sensor's cells are from our own published specifications.

I want one system to run the room.

Controllers. They switch climate equipment, lights and irrigation from their own sensors.

Agrowtek

SXC sensor: air temperature, humidity and PPFD, with CO₂ as an option.5

Full profile
Agrowtek: full profile
ControlsClimate, CO₂, lighting, irrigation and nutrient dosing, through GrowControl GCX controllers.6
Leaf temperatureOptional PLIR leaf sensor. VPD from air temperature, humidity and leaf temperature.5
AlertsEmail and text, from the GCX controller.6,7
Network and offlineEthernet to the GCX, Wi-Fi as an add-on. The GCX stores logs as CSV files.6
Connects toModbus RTU. The SXC works with a GrowControl GCX, a PC or a PLC, and the GCX exports CSV files.5,6
Listed priceSXC sensor $319. GCX controller $2,799.5,6

Grownetics

CropVision: zone-level VPD, CO₂, PAR and DLI, substrate water content and EC, runoff EC and pH.12

Full profile
Grownetics: full profile
ControlsUnity controls HVAC, dehumidification, heating, ventilation, CO₂ and lighting stages.13
Leaf temperatureNo leaf sensor listed.12,13
AlertsAlerting is part of its software. Channels not listed.14
Network and offlineUnity keeps running locally if the internet drops.13
Connects toDescribes an open ecosystem of sensors and platforms. No API details listed.12,13
Listed priceSoftware from $249 a month per facility. Hardware quoted.14

TrolMaster

Integration partner of Grow Sensor

Temperature, humidity, CO₂, light and PAR, plus substrate water content, EC and temperature.19,20

Full profile
TrolMaster: full profile
ControlsTemperature, humidity, CO₂, lights, airflow and irrigation, through Hydro-X and Tent-X controllers.19,20
Leaf temperatureNo leaf sensor listed.19,20
AlertsAlerts in the free TM+ Pro app.19,20
Network and offlineTent-X needs an Ethernet cable for remote alerts. What happens offline is not listed.20
Connects toIts own controllers, sensors and the TM+ Pro app. Other integrations not listed on the pages checked.19,20
Listed priceGreen-X greenhouse starter kit $550.21

I want irrigation steered from root-zone data.

Crop steering. They measure the root zone and run irrigation from it.

AROYA

Climate station (temperature, humidity, CO₂, VPD), TEROS ONE substrate sensors, feed and runoff EC, pH.1,3

Full profile
AROYA: full profile
ControlsIrrigation, from substrate data, through OpenSprinkler. Its Climate One station also triggers HVAC and dehumidification.2,3,4
Leaf temperatureNo leaf sensor listed. VPD from air temperature and humidity.1,3
AlertsNot listed on the pages checked.1,3,4
Network and offlineA wireless network provisioned by AROYA, through its gateway. What happens offline is not listed.1,3
Connects toOpenSprinkler and AROYA's own CCMS controller, plus any controller that speaks Modbus, including through TC Controls.22
Listed price$5K single-room starter.1

Grow Sensor

Climate, CO₂, light and spectrum in one canopy unit, plus substrate water content, EC and temperature through one probe.

Full profile
Grow Sensor: full profile
ControlsIrrigation, through crop steering with OpenSprinkler: Grow Sensor's steering software decides each shot and OpenSprinkler opens the valves. Climate equipment stays with the facility's controller.
Leaf temperatureInfrared leaf sensor built in, ±0.5 °C. VPD worked out at the leaf.
AlertsIn the app and as push notifications. No text, phone call or email.
Network and offline2.4 GHz Wi-Fi. Readings are logged on the sensor when the internet drops, and irrigation keeps running.
Connects toToday: OpenSprinkler for crop steering, Home Assistant over MQTT, an API on request, and substrate probes from METER Group, Delta-T, Acclima and Growlink. Coming soon: two-way Growlink data, Argus Controls, TrolMaster readings, Bluelab reservoir readings, and Claude and ChatGPT.
Listed priceComplete system £699 / €799 / $899. OpenSprinkler controller on request.

I need a phone to ring when something fails.

Alarms. Monitoring that calls, texts and emails people.

Sensaphone

Temperature, humidity, CO₂, power, water leaks, pH and soil moisture, plus third-party sensors.17,18

Full profile
Sensaphone: full profile
ControlsNone listed. Monitoring and alarms.17
Leaf temperatureNo leaf sensor or VPD listed.17,18
AlertsPhone call, text and email, to any number of contacts.17,18
Network and offlineCellular or Ethernet, up to 8 hours on battery. The cloud raises an alarm if the unit stops reporting.18
Connects toAny third-party analog or digital sensor; Sentinel Pro reads Modbus registers. Data exports from its web dashboard.17,18
Listed priceNo prices on the pages checked.17,18

I want readings and alerts at a published price, beside the controller I run.

Monitoring only. It measures and alerts, and leaves the equipment to the controller.

Pulse

Pulse One: temperature, humidity, VPD, dew point, light. Pulse Pro adds CO₂, PPFD, DLI and a spectrometer. Hub kits for substrate.15

Full profile
Pulse: full profile
ControlsNo equipment control listed.15
Leaf temperatureNo leaf sensor listed.15
AlertsEmail and push on every plan. Text on paid plans, US and Canada only.16
Network and offlineNot listed on the pages checked.15,16
Connects toAn API with daily data limits by plan, and CSV export.16
Listed pricePulse One $199. Pulse Pro $499.15

02 · Cost

What it costs to start.

One room, as each company lists it on 20 November 2026. Prices are in the currency each company publishes. We haven't added them up, because each one includes different things.

What one room costs to start, as listed on 20 November 2026
SystemListed priceWhat you buySoftware
Agrowtek$319 sensor. $2,799 GCX controller.SXC sensor, with CO₂ (+$119) and leaf temperature (+$169) as options. Control runs through a GCX controller.5,6No monthly fees.
AROYA$5KSingle-room starter: climate station, two TEROS ONE, Drip & Drain, pH sensors, gateway, two coaching sessions.1,4Free to start (the page says both 90 days and the first run). Later pricing follows a demo.
Grow Sensor£699 / €799 / $899. OpenSprinkler on request.Complete system: the Grow Sensor PRO and a SubSense substrate probe. Crop steering adds an OpenSprinkler controller.Grow app free. Crop steering needs Grow Plus or GrowOps; GrowOps from £49 / €59 / $65 a month, billed annually.
GrowneticsNot listed.Hardware and controls, quoted for the facility.14Cultivate $249 a month per facility. Automate $349.
Pulse$499. $799.Pulse Pro for the room. Hub VWC Kit for substrate.15,16Free, or $10 or $35 per user a month.
TrolMaster$550Green-X greenhouse starter kit for one room.19,21Free TM+ Pro app, no monthly fees.
What one room costs to start, as listed on 20 November 2026

Growlink and Sensaphone list no prices on the pages checked.8,10,17,18 Grow Sensor ships from the UK, so outside the UK import duty, import VAT and carrier fees are paid on delivery.

Grow Sensor pricing · Open the ROI calculator

03 · Leaf VPD

Air VPD assumes a leaf at air temperature.

Vapour pressure deficit: how much more water vapour the air could hold, in kPa. Growers steer transpiration with it. is the drying pull between a leaf and the air around it. Worked out from air temperature and humidity alone, it assumes the leaf is at air temperature.

Leaves often aren't. Transpiration cools them and radiant heat from the lights warms them. A leaf cooler than the air loses water more slowly than the air figure suggests. A warmer one loses it faster.

Worked example

Air 26 °C · 60 %RH · leaf 24 °C

VPD from the air
1.34 kPa
VPD at the leaf
0.97 kPa
The gap, same room
0.37 kPa
FIG. 02 · A leaf 2 °C under the air, as an example. Worked with the Tetens equation: saturation vapour pressure at the leaf's temperature, minus the vapour pressure the air holds. A leaf reading accurate to ±0.5 °C moves leaf VPD by about ±0.09 kPa here.

Three of the eight list a leaf sensor: Agrowtek (the PLIR option on its SXC sensor), Growlink (the Aranet IR Plant Temperature Sensor) and Grow Sensor (built into the PRO). AROYA, Grownetics, Pulse, Sensaphone and TrolMaster don't list one on the pages checked.1,3,5,9,12,15,17,19,20

What to do with a leaf reading.

  1. 01

    Ask which temperature the VPD figure uses. From air alone, it assumes the leaf is as warm as the air.

  2. 02

    Put the leaf and air figures side by side in one room, at lights on, mid-period and lights off. That gap is the part an air sensor misses.

  3. 03

    Set VPD limits against the leaf once you know that gap for the room and the phase.

04 · On the demo

Ten questions for any vendor.

Ask every vendor the same ten, and get the answers in writing. They cover what a demo tends to skip: placement, calibration, alerts, offline, cost and exit.

  1. 01

    Does it control equipment, or only measure?

    A controller takes over how the room runs. Monitoring is added next to what you have.

  2. 02

    Is VPD worked out from air temperature or a measured leaf?

    Air VPD assumes the leaf is as warm as the air. Under lights it often isn't.

  3. 03

    Where does each sensor sit, and how is it calibrated before it ships?

    Where it hangs and how it was calibrated both change the number you see.

  4. 04

    What needs recalibrating, and how often?

    Some readings, CO₂ especially, need checking over time. Ask who does it and what it costs.

  5. 05

    How does an alert reach a person?

    App, push, email, text or a phone call. Ask which ones reach someone off shift.

  6. 06

    What happens if the internet or the power drops?

    Ask whether readings are kept, whether control carries on, and who is told.

  7. 07

    What does one room cost to start, all in?

    Hardware, software, installation and network. Ask for the figure in writing.

  8. 08

    What is the software priced by, and what does year two cost?

    Rooms, sensors, users and canopy area give very different bills at scale.

  9. 09

    Is there a minimum term, and does the hardware work if we stop paying?

    Get the exit terms in writing before you sign.

  10. 10

    Can we export our own data, and what does it plug into?

    Controllers, probes and protocols decide what you can add later.

Weighing a quote from AROYA? See Grow Sensor and AROYA side by side.

05 · Pilot

Pilot one room first.

One room for one run shows more than any demo: how the readings hold up, whether the alerts reach the right phone, and how the support answers.

A grower in a flower room working at a laptop on a bench.
FIG. 03 · Reviewing a run in the room
  1. 01

    Pick one room you know well.

    A room with a few runs of history, so new readings have something to sit beside.

  2. 02

    Hang sensors where the plants are.

    At canopy height, at least one per room, and more for big or racked rooms. A sensor on the wall can read differently from the canopy.

  3. 03

    Run it for a full cycle.

    One run, clone to dry, is long enough to test the alerts and the support.

  4. 04

    Review the run.

    List what the system flagged and what it missed, then decide whether to buy for the facility.

Where Grow Sensor fits

A Grow Sensor PRO hanging on its cord just above the canopy in a flower room.

06 · Grow Sensor

Where Grow Sensor fits, and where it doesn't.

Everything above holds all eight to the same criteria. This part is ours.

Choose another system if

  • You want one system to run the climate.

    Agrowtek, Growlink, Grownetics and TrolMaster switch HVAC, dehumidifiers, CO₂ and lights. Grow Sensor steers irrigation and leaves the climate equipment to the controller.6,8,13,19

  • You want feed and runoff EC and pH in the starter kit.

    AROYA's single-room starter includes Drip & Drain and pH sensors. Grow Sensor reads the substrate through one probe per PRO.1

  • Someone must get a phone call or a text.

    Sensaphone calls, texts and emails. Agrowtek texts, and Pulse texts on paid plans in the US and Canada. Grow Sensor does none of these.6,16,18

  • The room can't rely on Wi-Fi.

    Sensaphone's Sentinel runs on cellular or Ethernet with a battery backup, and Agrowtek's GCX on Ethernet. Grow Sensor needs 2.4 GHz Wi-Fi.6,18

  • Your auditor wants EU-GACP paperwork from the supplier.

    Growlink lists support for EU-GACP Rev. 1, Annex 11 and Annex 15. Grow Sensor is CE and UKCA marked but lists no GMP or GACP credentials.11

Choose Grow Sensor if

  • You want VPD worked out from a measured leaf.

    An infrared leaf sensor sits in the canopy unit with climate, CO₂, light and spectrum, so VPD is worked out at the leaf.

  • You want irrigation steered from the root zone.

    Pick a steering style, from very generative to very vegetative. Grow Sensor's steering software decides each shot from the root-zone readings, and OpenSprinkler opens the valves.

  • You want to see the price first.

    A complete system is £699 / €799 / $899, GrowOps prices are published, and no contract is needed to start.

  • You already run a climate controller.

    Grow Sensor sits beside it and leaves the climate equipment alone. Growlink Terralink probes plug into the PRO today.

  • You want to start with one room.

    One complete system per room, or the Facility Starter Bundle at £649 / €749 / $849 a room for 2 to 5 rooms, with three data reviews.

For one system that runs the climate, choose a controller. To measure the leaf and steer irrigation beside the controller you have, choose Grow Sensor.

See Grow Sensor pricing
Nichilas Ezzo hanging a Grow Sensor in the canopy

Nichilas Ezzo

Head grower, FarmaceuticalRX

“I've never second guessed the readings.”

07 · Questions

What buyers ask before choosing.

There is no single best system. The right one depends on the job. Agrowtek, Growlink, Grownetics and TrolMaster control climate equipment. AROYA steers irrigation from substrate data. Grow Sensor does it with OpenSprinkler and measures leaf temperature, climate, CO₂, light and spectrum from one canopy unit. Sensaphone raises alarms by phone call, text and email. Pulse monitors the room at published prices and leaves the equipment to the controller.

As checked on 20 November 2026: AROYA lists a single-room starter at $5K. Agrowtek lists its SXC sensor at $319 and its GCX controller at $2,799. Grownetics lists software from $249 a month per facility, with hardware quoted. Pulse lists Pulse One at $199 and Pulse Pro at $499. TrolMaster lists a $550 Green-X greenhouse starter kit. Grow Sensor lists a complete system at £699 / €799 / $899. Growlink and Sensaphone list no prices on the pages checked.

Agrowtek offers leaf temperature as the PLIR option on its SXC sensor, for $169. Growlink sells the Aranet IR Plant Temperature Sensor. The Grow Sensor PRO has an infrared leaf sensor built in, accurate to ±0.5 °C. AROYA, Grownetics, Pulse, Sensaphone and TrolMaster don't list a leaf temperature sensor on the pages checked on 20 November 2026.

Agrowtek, Growlink, Grownetics (with Unity) and TrolMaster control climate equipment. AROYA runs irrigation and triggers HVAC and dehumidification from its Climate One station. Grow Sensor steers irrigation through OpenSprinkler and leaves climate equipment to the facility's controller. Pulse and Sensaphone monitor and alert, and don't switch equipment.

Sensaphone calls, texts and emails alarms to any number of contacts. Agrowtek's GCX controller sends email and text alerts. Pulse sends email and push alerts on every plan, and texts on paid plans in the US and Canada. TrolMaster alerts through its free TM+ Pro app. Grow Sensor sends alerts in the app and as push notifications, with no text, phone call or email.

Growlink lists an open API with REST and webhooks, plus BACnet, Modbus, SDI-12 and MQTT. Pulse lists an API with daily data limits by plan. AROYA connects to OpenSprinkler, its own CCMS controller and any controller that speaks Modbus. Agrowtek works over Modbus with its GCX controllers, a PC or a PLC. Grow Sensor connects to OpenSprinkler for crop steering and to Home Assistant over MQTT, with an API on request; two-way Growlink data, Argus Controls, TrolMaster, Bluelab, Claude and ChatGPT are coming soon. Grownetics and TrolMaster list no API details on the pages checked.

08 · Method

How we compared.

We make Grow Sensor, so this page isn't neutral. These are the rules we held it to.

Every fact about the other seven comes from that company's own website, read on 20 November 2026. Each one carries a number that links to the page it came from.

Prices are the ones each company lists. Where a company lists none, the guide says so. We don't use resellers', roundups' or forum figures.

Systems are grouped by the job their own websites describe and listed alphabetically inside each group. There is no ranking.

Growlink and TrolMaster are integration partners of Grow Sensor. Growlink Terralink probes plug into the Grow Sensor PRO today. Two-way Growlink data and TrolMaster readings in GrowOps are coming soon. Both are held to the same criteria as everyone else.

Spotted something out of date? Tell us and we'll correct it.

  • How alerts reach a person for AROYA and Grownetics, and for Growlink beyond its app.
  • What happens to readings when the internet drops for AROYA, Pulse and TrolMaster.
  • Whether AROYA, Agrowtek, Grownetics, Pulse and Sensaphone sell in the UK and Europe.
  • Contract and exit terms for the other seven.
  • Accuracy in a working room. Specifications are the makers' own figures. We haven't field-tested them.

Want a price for your rooms?

Tell us about your facility. We'll send your exact hardware and monthly cost within a business day.